I went ahead and checked out the Blue Ox Tow Bar Wiring Kit BLU79FR, and it actually is only deigned to fit the 2018-2021 Jeep Wranglers.
Instead, I recommend installing the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM56200.
This wiring harness will plug directly into your vehicle's wiring harness, and is guaranteed to fit your 2008 Jeep Wrangler. view full answer...
Chris, we don't have the Protek 100 that you're talking about, but we do have the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # TK67FR which sounds like what you're looking for.
This wiring harness is custom fit to your vehicle, so there won't be any splicing or cutting required, comes with the ModuLite circuit protector pre-installed, and wires directly to the battery to avoid overloading your Mazda's electrical system. view full answer...
Hey Jeff, yes the Blue Ox base plate kit part # BX4104 is the correct fit for your 2008 Hummer H3.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.... view full answer...
Hey Ramiro, thanks for reaching out!
I recommend using the ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT for your 2022 Volkswagen Golf GTI because it's powered by your vehicle battery and it uses clamps to sense when to send signals to the trailer lights.
At this point in time there aren't any custom-fit harnesses for your vehicle so a universal fit like this is what you'll need to use.
The instructions for this wiring kit can be a little intimidating but if you're into DIY... view full answer...
Hey Patrick, so I took a peek and what we have for you and I was able to find the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM39VR which is a custom fitting harness that plugs into your existing wiring without splicing.
As far as the Roadmaster Stop Light Switch Kit # RM-751490 goes, you are going to need that with your Roadmaster Even Brake Portable Flat Tow Brake System # RM-9400 to complete install. You're also going to need the 12 Volt Outlet Kit, 20 amps # RM-9332. view full answer...
A LED Brake Light Hitch Cover will fit into the etrailer Trailer Hitch Receiver # e93ZR you installed on your 2021 Nissan Rogue. The light needs to plug into a 4-way flat connector so you will also need the Curt T-Connector Vehicle Wiring Harness # C44ER to install on your Nissan Rogue. Hitch covers with a light like this will all use this style connector since the vehicle is most likely going to have trailer wiring with a trailer hitch receiver installed. view full answer...
The Curt T-Connector Vehicle Wiring Harness # C56136 is a custom fit harness for the 2009 Scion xD which has incandescent tail lights. If you have the optional LED tail lights there is not a plug and play kit but you will instead need to tap into the tail light wiring with the Curt Powered Tail Light Converter # C59236 which will also require a power wire ran to the battery. view full answer...
The Curt Trailer Hitch Receiver # C13388 has been confirmed by Curt to fit your 2023 Mercedes-Benz Sprinter 1500. This has the more common 2" opening allowing for a larger selection of Ball Mounts # C45534 and hitch mounted accessories.
As I do not see anyone with a wiring harness custom fit for your Sprinter we have the Tekonsha # 119250KIT universal 4-way which will detect power going through the tail light wiring. This way you will not have to splice into the factory wiring. view full answer...
Hey Bill, yes the Bargman 5th wheel/gooseneck 7-way kit part # 54700-003 does fit your 2003 Ford F-350. It plugs inline with your current 7-way and will allow the current trailer wiring you have now to function just like normal. view full answer...
We do have options for a wiring harness to go with the etrailer # e65KR on your 2022 Genesis GV80. Since there is no custom fit option, you will need the Vehicle Wiring Harness Kit w/ 4-Pole Trailer Connector and Installation Kit # C59496. This is a universal wiring harness which will require splicing into your existing wiring for installation. Once installed, you will have a 4-way connection at the back of your vehicle to power your trailer's signal lights.
If you would like to avoid... view full answer...
Yes, we do have a hitch for the 2024 Mazda CX-90. It is the Curt item # C25FV. This hitch is custom fit and bolts to your Mazda with included hardware. This is a class III hitch with a 2" receiver. It has a 5,000 lbs towing capacity and a 500 lbs maximum tongue weight.
I really like this hitch because the entire crosstube mounts behind the rear bumper. This leaves only the 2" receiver exposed which not only looks better but helps with ground clearance.
The Curt T-Connector Vehicle Wiring... view full answer...
Tekonsha actually says there are no custom fit electrical wiring products for your 2016 BMW X3. I'm not entirely sure what you were looking at, perhaps it was a different year or model since you said you couldn't find one for the 2016. The # 119250KIT we list is a universal wiring harness so we know it will fit your vehicle. This uses the zero-contact interface sensors that clamp onto the wires. It is the only option that will not require splicing. The only other option for a wiring harness... view full answer...
Hey Timothy, sorry about how U-Haul totally screwed the pooch and sent you home with the wrong trailer wiring for your 2018 Toyota RAV4 Hybrid. We have the Tekonsha kit part # 118578 that fits your vehicle and would be a great option. It installs inline with your taillight connectors and comes with the most reliable converter box. I attached a picture of a review for this kit on a similar 18 Rav4 hybrid for you to check out as well. view full answer...
Hey Dave,
The Curt Custom Tail Light Wiring Kit for Towed Vehicles # C96JR would not be intertwined or interfere with the Blue Ox Patriot # BLU37TR. This wire harness is simply plugging into the motorhome and Gladiator tail lights to copy the light signals from the motorhome over to the Gladiator. If you active the brakes in the motorhome the light will transfer over to the Gladiator and the Patriot would sense the decrease in inertia and activate. You shouldn't have an issues using these... view full answer...
For a hitch that fits your 2022 Toyota Sienna I recommend the Curt Trailer Hitch Receiver # C22UR. This is a custom fit hitch with a 2" receiver and maximum gross trailer weight of 3,500 lbs so it matches the towing capacity of your vehicle. It features a gloss black powder coat finish and comes with a limited lifetime warranty.
Since you plan on towing you will also need wiring and a ball mount. I recommend the Tekonsha T-One Vehicle Wiring Harness # TK69FR since it is the most reliable.... view full answer...
The Blue Ox Tow Bar Wiring Kit BLU86XR you mentioned is actually designed to fit 2014-2022 Jeep Grand Cherokee's with a tow package, as well as a 2022 Jeep Grand Cherokee without a tow package. With that being said, this kit is not going to be the correct kit for your 2021 Jeep Wrangler, unfortunately.
Instead, what you're going to need instead is the Curt Custom Tail Light Wiring Kit for Towed Vehicles # C96JR.
This is going to be the same wiring harness as the Blue Ox Tow Bar Wiring... view full answer...
Hey there Bill; thanks for the question, and I can verify for you that yes, the etrailer hitch will 100% fit your 2023 Hyundai Santa Fe hybrid. The correct part number is the following:
- etrailer Trailer Hitch Receiver # e28AR
I double-checked on this for you just to make absolutely sure, and you can definitely use it on your hybrid. I also added a cut out from a customer review showing they put it on their hybrid.
And since you mentioned towing, if you also need a 4-way wiring harness,... view full answer...
The best hitch for your 2013 Hyundai Sonata Hybrid is going to be the Draw-Tite item # 24965. This hitch is custom fit for the hybrid models and bolts to your car with included hardware. It is the strongest and safest hitch available for your Sonata.
I have linked an installation video below to help you get it set up.
Since you are planning on towing you will also need a wiring harness item # C59236 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2... view full answer...
Hey Mike, thanks for ordering the Curt Hitch # C13416 and Wiring # C56434 for your 2019 Toyota RAV4!
Since you installed the T-Connector style the easiest way to see what's going on is to disconnect the Curt tees and plug in your RAV4 tail lights directly to the vehicle wiring and see if that fixes your issues. If that does then something is going on with the Curt wiring like the connectors weren't seated properly or the black converter box is messed up.
If the connectors are seated properly... view full answer...
It depends on what trailer you'd consider to be "most" trailers, but with a Tesla you're going to be pretty limited so I'll assume it's nothing with brakes.
So with that being said, we have the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT, which is a custom fit harness that'll simply plug into your factory wiring. This is a 4 pole wiring harness which is pretty much that standard on every small trailer.
It's also worth... view full answer...
Go To Results